Versions Compared

Version Old Version 2 New Version Current
Changes made by

Jason Berry

Jason Berry

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

At boot, the LED’s will flash an RGB pattern to test the lights. It will then flash each switch mode, followed by the MIDI channel (status pixel is blue in this stage), followed by the firmware version (status pixel is white in this stage).

The Firmware version, Red flashes are the major version, and green the minor.

If you’re in Snapshot mode, at this point it’ll flash green LEDs to let you know it’s in snapshot mode. If not, it’ll light up the switches with their repective footswitch pixel color helping denote the mode.

When the unit is fully powered up and in it’s running state, the status pixel no longer means anything related to footswitch programming. Right now it’ll simply light up Red and stay on, but we’ll be adding things in the future such as it flashing to the tap tempo beat/etc.

PixelLabels.jpgImage Added

To change what each footswitch does:

...

Function

LED Color (Status Pixel / Footswitch Pixel)

FS4 (Left footswitch default setting)

Red / Red

FS5 (Middle footswitch default setting)

Red / Green

Preset Down

Red / Blue

Preset Up

Red / Purple

Previous Footswitch Mode

Red / White

Next Footswitch Mode

Red / Yellow

Previous Snapshot

Green / Red

Next Snapshot

Green / Green

Snapshot 1

Green / Blue (Deprecated, Use Snapshot Mode)

Snapshot 2

Green / Purple (Deprecated, Use Snapshot Mode)

Snapshot 3

Green / White (Deprecated, Use Snapshot Mode)

Snapshot 4 (HXStomp XL Only)

Green / Yellow

Tuner

Blue / Red

Tap Tempo/Hold-For-Tuner (Right footswitch default setting)

Blue / Blue

CC 101 Val 0 (every press)

Blue / Purple

CC 101 Val 0 / Val 127 (toggles every press)

Blue / White

CC 102 Val 0 (every press)

Blue / Yellow

CC 102 Val 0 / Val 127 (toggles every press)

Purple / Red

CC 103 Val 0 (every press)

Purple / Green

CC 103 Val 0 / Val 127 (toggles every press)

Purple / Blue

FS7 (HXStomp XL Only)

Purple / Purple

FS8 (HXStomp XL Only)

Purple / White

...

  1. During boot press & hold the middle switch until the status pixel turns solid blue

  2. Release the middle switch, and the current MIDI channel will flash on the Footswitch 1 oixel:

    1. A red flash means +5

    2. A green flash means +1

      1. Example - Channel 1 = 1 green flash

      2. Example - Channel 7 = 1 red flash + 2 green flashes

      3. Example - Channel 14 - 3 red flashes + 4 green flashes

  3. The Left switch decrements the channel by 1, while the Middle switch increments by 1

  4. Wait 10 seconds and it’ll automatically save

Snapshot Mode:Hold

#2 for snapshot mode. till status pixel goes solid, release, then #2 changes; flood white == enable, flood red == disabledSnapshot mode puts the 3 switches into a mode where the 3 switches & their LED’s represent the 3 snapshots available on the HXStomp. Please note that when switching presets, the HX does not provide a way to “follow” the snapshot so after changing to a bank, press a footswitch to sync back up what snapshot is active.

To get into Snapshot mode:

  1. During boot press and hold the right switch until the status pixel turns solid green, then release

  2. The far right switch turns snapshot mode on and off.

    1. All-white == snapshot mode

    2. All-red == not snapshot mode; i.e do the regular programmed footswitch commands from above

  3. While in Snapshot mode:

    1. Firmware < 2.1

      1. Hold Left Switch for FS4

      2. Hold Middle Switch for FS5

      3. Hold Right Switch for Tuner

    2. Firmware 2.1+

      1. The commands sent when folding footswitches in Snapshot mode are configurable via the “To change what each footswitch does” section above